Duff5000 » user profile

3
Member Since 23/04/2009
Last Seen 7 hours 46 min
Location Melbourne

Recent Activities

I am using one of these generic Chinese adjustable DPI mouses now. After about a year the cord broke, swapped it out with another USB and...
21/07/2016 - 15:41
buy selling you other stuff on their page. Warning, their other stuff isn't work safe.
21/07/2016 - 10:37
Return them to save $3? Not really worth the effort.
10/07/2016 - 18:08
I am pretty sure RC was cheaper to run than gas last time i read about it but i don't have anything at hand to back that up. Also, depends...
09/07/2016 - 00:21
Your fan one was probably better. Convection heaters make hot air rise out of them. The hot air just pools at the ceiling until it cools....
08/07/2016 - 00:59
Picked one up yesterday. Bargain! Apparently there were still plenty at glen waverly and waverly gardens, call to check if you are still...
07/07/2016 - 22:29
Thanks for that, Changed the overscan for HDMI and DTV Any chance you have a link to more info on what the other settings mean? eg "power...
07/07/2016 - 22:25
That is where i ended up as well. The default is bad. Movie mode seems about average for tv inbuilt speakers. I was using optical out on my...
07/07/2016 - 22:12
Bummer none in the south east then
05/07/2016 - 15:32
Anyone find out by any chance?
05/07/2016 - 13:58
Is the soniq you mentioned this one?...
04/07/2016 - 22:43
Anyone got one yet? How loud is it? edit: nevermind apparently direct drive is much louder. "Quietness - A direct drive compressor is...
25/06/2016 - 11:41
There's another version of the body cap lens, a fisheye 9mm. That is heaps more useful and actually takes excellent pics. Highly recommend.
24/06/2016 - 16:27
Not really much difference with electric heaters. They all are pretty much equally efficient. Reverse cycle air con is much more efficient...
22/06/2016 - 22:25
Gave them a good workout today. Put in 100 10x100mm batten screws before i ran out of battery. Well technically 99.75 as i didn't quite get...
22/06/2016 - 21:33
[@raiichiu](/comment/3792609/redir): Sure no clamp but it is "skid proof"!
20/06/2016 - 20:19
I bought one of these for a couple of $$. I dont recall my one being "skid proof" though!
20/06/2016 - 20:18
[@allergic2work](/comment/3791573/redir): i bought the jig kit and a couple of boxes of screws from amazon. Delivered all up was less than...
20/06/2016 - 11:43
Only used one bit doing my deck (6.5x4.2M) Used this though and the driver bit is quite long and hard to lose:...
20/06/2016 - 10:58
Seems decent. Doubt you will have much use for all the square bits though but the rest should be useful.
20/06/2016 - 10:46
Oh, i couldn't see the aldi one online so i didn't know the specs. If you need the hammer then this is a decent deal:...
19/06/2016 - 20:28
That doesn't sound like much of a deal. If it isnt brushless and it is a generic brand you might as well get this:...
19/06/2016 - 11:26
1.5 actually is the lower limit, 1.5-13mm is written on the drill.
19/06/2016 - 00:45
There is probably a warranty agent listed in the instructions. Essentially there is no difference between the 18 and 20v. Just different...
18/06/2016 - 21:58
Pretty sure it needs to have a gap or it wouldn't have a good hold of bits. Either way, if you are wanting to drill with bits smaller than...
18/06/2016 - 17:13
Probably becasue the motor is more exposed in these, also high voltage. Crappy drills with tiny motors normally you cant see much in....
17/06/2016 - 22:52
Ignoring the fabrication of a new base for the battery would it be hard to install 2 banks of 5 in parallel to get 4Ah (or 7.1Ah when the...
17/06/2016 - 09:54