demod » user profile

1 2
Member Since 20/09/2011
Last Seen 1 hour 31 min
Location Sydney

Recent Activities

Yeah I had a bunch of trouble at the start, ended up being because I was using a mini-usb hub as a usb extension . So I think I flashed...
16/11/2018 - 09:19
So far so good. My comments are re: passwords, not sure why passwords don't pop up as they do in chrome? I did get a keepass request, which...
15/11/2018 - 14:31
the russian forums! haha killing me. Nope, didn't see that registry edit. I ended up using linux, for balong_usbloader and balongflash. I...
14/11/2018 - 10:05
Would love to know how you did it too. I'm still going through this pain. But I've also locked with too many attempts to unlock, used...
14/11/2018 - 09:36
definitely good to go. nothing wrong with your hardware there. I've only used the arduino IDE for flashing. Can sometimes take a few goes...
07/11/2018 - 13:02
If you set the baud rate to 74880 You should get something like (sorry, i just guessed the speed above) >ets Jan 8 2013,rst cause:2, boot...
06/11/2018 - 09:11
Choose the "Teckin" module, and everything except the button will work. You can get the button working by creating your own profile and...
05/11/2018 - 15:02
https://www.ebay.com.au/itm/NEW-Samsung-WW85J54E0IW-8-5kg-Front-Load-Washer/123068849165
04/11/2018 - 10:40
Grabbed a Samsung 8.5kg front loader on Friday for ~$639 ($631 after CR!). "Luckily" the existing 9 yr old unit broke its spider drum mount...
04/11/2018 - 10:00
No, you should see output in a terminal. Open putty and you should see some output. 778000 baud or something similar should show the...
03/11/2018 - 10:20
can you see any output on the serial port when the plug powers up? Even garbage? If not swap your TX and RX line around and try again.
03/11/2018 - 00:00
Might be running down a rabbit hole, but. I configured up a new model in tasmota that was exactly the same as the "Teckin" module except...
19/10/2018 - 01:27
Correct about the DC supply. I set the scope up with two probes and no earth, in a differential setup. Its a blur of about 1v above and...
18/10/2018 - 22:00
I used one of those power meter sockets (from aldi too). It tells me the voltage, Amps, and Watts of the device plugged into it. The...
18/10/2018 - 10:15
looks like it was only added a week ago :), how lucky is that. I compiled from the git source so must have already been in there. Using the...
17/10/2018 - 23:15
yep, looks like it. enabled last night, was in the same state this morning. Put it all back together, and in the house. Has been running 6...
17/10/2018 - 16:04
Almost 100% :) - the button doesn't work. got very accurate power display by using a powermeter, and using commands "powerset <watts>" and...
17/10/2018 - 09:28
I can confirm the Medion smartswitch is 100% supported and working with the Tasmota firmware setup as a Tekin module. No custom code...
17/10/2018 - 08:21
Thanks for the tip on the BL0937. Looks the the "Teckin" device is the closest match to our Medion. When model is changed to Teckin, I can...
16/10/2018 - 23:15
I think you are right, the earth pin just passes straight through the smart switch. The 3.3v is floating. I might measure the -ve pin...
16/10/2018 - 22:13
Needs the app to get an IP
16/10/2018 - 20:02
I've got Tasmota flashed. also did a few generic test uploads first to make sure I had everything in order. Was a PITA getting the triangle...
16/10/2018 - 17:55
@AuSlade I agree. I'm about to pull one apart, and flash some custom code. See if it still switches randomly. Then we'll know if its...
16/10/2018 - 11:39
Anyone heard back from Jovan?
16/10/2018 - 10:26
Have had a brand new unit unconfigured - straight out of the box, sitting behind a UPS (which filters lots of noise etc), just turned off...
15/10/2018 - 18:42
wow.. already switched off!
15/10/2018 - 11:13
Bought 3 yesterday, set one up last night on the Tuya app (mainly because Medion app wouldn't email the reg code). Put it on a laptop...
15/10/2018 - 09:31
yep, typical. 6000 points expired 3 days ago!
04/09/2018 - 16:21
I just received this too. Bit weird, since I picked up my order an hour ago.
23/08/2018 - 12:12