zerocritical » user profile

Member Since 26/12/2012
Last Seen 19/04/2024
Badges 3
Location Sydney

Recent Activities

Have a look at Skoda Kodiaq.
30/03/2024 - 07:46
Powered by eneloops!!
24/02/2024 - 08:54
Sounds like a Wifi issue.. either your router is too far or your wifi network is overloaded
16/08/2023 - 07:20
Its most likely your router / wifi issue and not the module.
15/08/2023 - 08:34
Are you logged in with a different email? the email address need to match the one used for $50 voucher for it to work.
21/03/2023 - 12:38
zerocritical was awarded a badge.
23/12/2022 - 08:17
Need a private investigator to locate OP who has done a runner after writing this post. Any recommendations?
04/11/2022 - 09:13
^^ This. For this sole reason, I'll probably never go 5G irrespective how higher the speed is or how low the cost is unless there is a way…
10/10/2022 - 07:42
Rounding the last 8 brings it to $6.00 not $5.99
05/03/2022 - 11:11
I had so many bad experiences with TPG for both internet and mobile services in past that I'll not go anywhere near them. Check Aussie BB…
24/11/2021 - 07:26
I used DaHai Zhu's firmware from this link. https://jgaurorawiki.com/jgmaker-magic
20/09/2021 - 05:57
One more thing to add, if you have a spare raspberry Pi lying around, I'd highly recommend octoprint with a webcam. Makes it so easy to…
16/09/2021 - 08:18
Just a quick initial thoughts on this printer. I bit the bullet and bought this as my first 3D printer and have been doing a lot of…
16/09/2021 - 08:14
Not much but the prints stick quite firm in the centre and hard to remove where as if I adjust the sides to slightly lower, print doesn't…
13/09/2021 - 16:21
I received mine today. I've set it up and tried to level the bed, corners level just fine but it seems raised from centre. Any ideas OP?
11/09/2021 - 23:03
I mainly need it for printing tablet wall mounts. Not sure what type of filament would be best suited for it.
01/09/2021 - 12:51
Hi Op, Any recommendation for the print area of atleast 300mm width?
01/09/2021 - 10:26
Thank you, makes sense
28/07/2021 - 16:59
Hi OP, In currently looking to renovate my house, it's a ~60 year old single habitable floor house on a sidewards sloping land. I say…
28/07/2021 - 07:42
Updated the title, thanks for highlighting desk fans can't be shipped
22/07/2021 - 12:14
Yes, as mentioned above I ordered misting fan and foldaway fan. Looks like other models are not available to be shipped to Australia.…
22/07/2021 - 12:05
Yes, from flash sale. After you said I tried to add other desk fans and had that issue. Very strange. Looks like the only ones working are…
22/07/2021 - 11:58
Yes I've ordered the misting fan and foldaway fan this time. Last year ordered the 10000mah clip on fan. All with shipping address in…
22/07/2021 - 10:00
I noticed that with some product like neck fan. Others were OK to ship
22/07/2021 - 08:15
What's wrong with using Shopify as their platform? Have you seen / used their products before calling them generic overpriced?
22/07/2021 - 06:54
Yeah it has slow shipping but I personally like their fans, great for camping and caravans. This deal shows 3-4 week shipping time
22/07/2021 - 04:36
Opolar Fan Sale: Misting 10000mAh US$15.50 (~A$21.05), Foldaway 10000mAh US$14.50 (~A$19.70) Delivered @ Opolar
Further 50% off (shows in cart) on top of already discounted fans. Ex: 10000mah misting clip on fan USD $15.50…
22/07/2021 - 04:12
Sure, just place a paid order and spread the word around. Small businesses rely on word of mouth.
14/07/2021 - 22:33
What happened to all the eneloop ozbargainers have been collecting? Just use that for the car battery.
02/07/2021 - 09:37
Loading...